Showing results: 856 - 870 of 1660 items found.
-
M41d -
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata M41d HBR3 Video Analyzer/Generator for DisplayPort Testing is a compact versatile test instrument offering entry level functional testing that can be extended through software licenses to a full compliance tester with sophisticated analysis and diagnostic capabilities. The M41d enables design and test engineers to validate their products for interoperability and reliability for the DisplayPort 1.4 video interface. The M41d is a flexible test instrument that can be upgraded from a functional tester for sources and sinks to a sophisticated analyzer and, if desired, can test full standards compliance, enabling developers to pre-test or self-test independently, reducing delays and costs during the product development cycle.
-
Badger Meter
The Portable Small Meter Tester (PSMT) is a lightweight system for field testing of 5/81 in. meters. It includes a test meter with control valves, hose connections, fittings and pressure gauge. Meter tests can be done without removing them from service. The inlet control valve ensures an accurate test start and stop. A globe valve downstream from the meter allows flow rate adjustment during test. Connection to the PSMT is made using standard 3/4 in. male hose connections located on the exterior of the case. Two 3/4 x 39 in. metal-reinforced flexible hoses are provided for easy field connections.
-
VOT-53 -
Standard Electric Works Co., Ltd
● 2000-count digital display (LCD type). ● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test ● Audible continuity test.● Auto sensing function for: voltage (AC/DC), Ω, diode.● Measurement function: ACV/DCV: 1000V Resistance: 2000Ω Frequency: 30Hz~1kHz ● Phase rotation test : ● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● Flashlight function.● Safety standard : EN 61010-1 CAT III 1000V EN 61010-1 CAT IV 600V EN 61243-3 EN 61326-1
-
Huntron
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design. Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
-
National Technical Systems
Gravelometer testing is designed to evaluate the resistance of vehicle surface coatings (paint, clear coats, metallic plating, etc.) to chipping caused by the impacts of gravel and other flying objects in accordance with SAE and ASTM standards. The primary usage of this test is to simulate the effects of the impact of gravel or other debris on automotive parts. Test samples are typically mounted in the back of the Gravelometer, and air pressure is used to project 1 pint (approximately 300 pieces) of gravel at the sample. The test sample is then removed and gently wiped off with a clean cloth. Tape is then applied to the entire tested surface. Removal of the tape then pulls off any loose fragments of the coating. The appearance of the tested sample is then compared to standard transparencies supplied by SAE to determine the chipping ratings. Visual examination can also be used to describe where in the coating/substrate system that the failure has been induced.
-
IBEKO Power AB
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
ISequenceSpec -
Agnisys, Inc.
The complexity of modern SoC has raised the requirement for HW/SW co-simulation to catch the bugs from the early design stage. There is lack of common set of sequences which can be shared across the teams. ISepenceSpec helps design teams to generate the unified test and programming sequences in UVM and Firmware from the specification. ISequenceSpec uses the register information from importing the standard formats like IP-XACT, SystemRDL, XML. User can define the test sequences in a simple editor, and then generate the unified test sequences from verification to validation.
-
HIL 6 series -
Typhoon HIL, Inc.
With 20 ns PWM sampling time, down to 500 ns simulation time step, and ultra-low latency, 6 Series processor has set the industry standard for ultra-high fidelity real-time emulation of power electronics systems. Simply plug your controller into a Typhoon HIL 6 Series real-time emulator, without any controller modifications, and take it for the most demanding test drive ever. Test any and all imaginable operating conditions, including faults. Automate and formalize test processes with our integrated software tools.
-
Bitbar Inc
Selenium has already cemented its place as a de-facto web test automation standard and Appium is providing very clean high level API that can be quickly adopted by Selenium developers, as it nicely abstracts lot of the messy stuff related to running tests. Our Testdroid Cloud provides this sort of environment where everything is packaged and pre-build for your Selenium / Appium tests, using only real mobile devices (Android and iOS) and real browsers that are usable with those devices (Safari for iOS, Chrome, WebKit, Firefox and others for Android).
-
TA-3C -
Tech-Aid Products
The TA-3C test fixture is a combination of the KMD540 testing requirements and the RDR-2000/2100 weather radar interface requirements. This panel allows the technician to test the KMD540 MFD as a stand alone item (with external simulators) or together with a radar sensor for a dynamic real time test. The panel includes the required switching for sensor alignment and KMD testing along with input jacks for the required data inputs. Also built into the fixture is an analog gyro simulator for checking the stabilization functions of the sensor. The full enclosure comes in standard panel width.
-
Bloomy Controls, Inc.
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
LX-30A+ -
Shenzhen Lian Xin Technology Co., Ltd.
Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .．·used to test single – ends ,double –ends ,three-ends power supply cords.．·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,．·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,
-
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
M9120A -
Keysight Technologies
The M9120A high-density matrix offers higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This 2-wire switch matrix provides the durable armature switches allowing multiple channels to be connected at one time, up to 60W per channel. The 4-wire wide bus can be used to route signals between test instruments and the device under test. Choose from the durable connector block or standard cable connections.
